Tulsa Plumbing and Air logoTulsa Plumbing & Air

Water Heater Installation in Tulsa, OK

Water heater installation in Tulsa usually costs $1,300 to $2,800 for a standard 40 or 50 gallon gas or electric tank, and $3,000 to $5,500 for tankless. The price includes the unit, labor, a City of Tulsa permit and hauling away the old tank. Most tank swaps take 3 to 5 hours.

  • Upfront price ranges
  • Licensed local pros
  • Tulsa County ZIPs only

Get a free quote

Takes 30 seconds. We share your request with a local pro.

Do you own the home?
Plumber connecting copper lines to a new tank water heater in a Tulsa, OK garage
Water Heater Installation in Tulsa, OK: typical work a licensed Tulsa-area pro handles.

Signs you need a new water heater

A leak from the tank body cannot be repaired. A leak from a fitting, the drain valve or the T&P relief valve often can be, so check where the water comes from before deciding.

  • The tank is 10 or more years old. The year is in the serial number on the label.
  • Water is pooling under the tank, or the tank body itself is wet.
  • Hot water runs out faster than it used to, which often means heavy sediment.
  • Rusty or brown hot water while the cold water is clear.
  • Popping or rumbling sounds while the burner or elements heat.
  • The burner, thermostat or gas valve has failed and the tank is past 8 years old.

Gas vs electric water heaters

Most Tulsa homes with gas service from ONG use a gas water heater. A gas tank heats water faster: a 40 gallon gas tank recovers about 40 gallons per hour, while a 50 gallon electric tank recovers about 20 to 25 gallons per hour. That matters for back-to-back showers.

Electric tanks cost less to buy and install because they need no venting or gas line, and they last a little longer. A heat pump water heater uses about one third of the electricity of a standard electric tank but needs about 700 cubic feet of space around it and works best in a garage or large utility room.

Gas tankElectric tankGas tankless
Upfront costMediumLowestHighest
Recovery speedFastSlowEndless
Needs ventingYesNoYes, special vent
Works in power outageMost modelsNoNo
Typical life8 – 12 years10 – 13 years18 – 20 years

How to make a new water heater last

  • Flush the tank once a year to remove sediment.
  • Check the anode rod every 3 to 4 years and replace it when it is worn to the wire. A new anode costs $20 to $60 plus labor.
  • Test the T&P valve once a year by lifting the lever for a second.
  • Set the thermostat to 120°F. It saves energy and cuts scald risk.
  • Keep 2 feet of clear space around gas units so the burner gets air.

Want a real price for your home?

Get a quote

Warranty terms to read before you sign

Most tank water heaters carry a 6, 9 or 12-year manufacturer warranty on the tank itself, which usually only replaces the unit, not labor. Ask the installer for a separate labor warranty, typically 1 to 2 years, since that covers the cost of removing and resetting a defective unit.

Tankless units often carry 10 to 15-year warranties on the heat exchanger but require proof of an annual descale to stay valid. Keep the service receipt each year.

Water heater installation cost in Tulsa

These are typical installed prices in the Tulsa area. The plumber's written quote is the real number.

Water heater typeTypical installed priceLife
40 gal gas tank$1,400 – $2,3008 – 12 years
50 gal gas tank$1,600 – $2,8008 – 12 years
50 gal electric tank$1,300 – $2,40010 – 13 years
Gas tankless (whole house)$3,000 – $5,50018 – 20 years
Heat pump (hybrid) electric$2,800 – $4,50012 – 15 years

Code items Tulsa inspectors check

A licensed plumber knows the current code version the City of Tulsa enforces. If any of these are missing on your old install, they get added during the replacement, which is why a quote can be higher than the price of the tank alone.

  • T&P relief valve with a discharge pipe running to within 6 inches of the floor or to the outside.
  • Thermal expansion tank on closed systems.
  • Gas units in garages raised 18 inches off the floor.
  • Drain pan with a drain line for attic and upstairs units.
  • Correct vent pipe size, slope and clearance to wood.
  • Gas shut-off valve and sediment trap at the gas connection.
  • Seismic or strap restraint if required by the local code version in force.

Choosing an installer for a water heater

  • Confirm the installer is a licensed Oklahoma plumber, checkable on the CIB website.
  • Ask if the price includes the City of Tulsa permit or if that is extra.
  • Get the brand, model number and warranty length in writing before the old tank is removed.
  • Ask what happens to the old tank: haul-away should be included.
  • Get a written quote comparing at least two installers for a job this size.

Energy and rebate notes

  • PSO (electric) and ONG (gas) in the Tulsa area post rebates from time to time on efficient water heaters; ask your installer or check the utility websites before buying.
  • A heat pump electric water heater uses about one-third the power of a standard electric tank, which can offset a higher purchase price over several years.
  • ENERGY STAR-rated gas tankless units qualify for some manufacturer rebates; ask the installer which models currently qualify.

Common installation mistakes to avoid

A water heater set without a drain pan in an attic or upstairs closet risks ceiling damage if it ever leaks. An expansion tank left off a closed system can shorten the tank's life through constant pressure swings. A gas line sized too small for a tankless unit causes poor hot water flow during heavy use.

Ask the installer to walk through each of these items on your specific setup before the job is marked complete.

Parts a code-compliant water heater installation needs

Ask the plumber to list these items on the water heater installation quote. A low price for water heater installation in Tulsa often leaves out the expansion tank or the permit, and those items show up when the City of Tulsa inspector visits.

  • A temperature and pressure (T&P) relief valve with a discharge pipe that runs to within 6 inches of the floor or to a drain.
  • A thermal expansion tank when the home has a pressure-reducing valve or a check valve on the main line, which is common in Tulsa homes built after 1990.
  • For gas units, a sediment trap (drip leg) on the gas line and a vent pipe with the correct slope and clearances.
  • A drain pan with a drain line when the new water heater installation sits in an attic, closet or above a finished floor.
  • A stand that lifts the burner of a gas water heater 18 inches off the garage floor, unless the unit is rated flammable-vapor resistant.

What raises the price

  • Code updates: a new expansion tank ($150 – $350), a drain pan, or new venting.
  • Attic installs: carrying a tank into an attic adds labor, and it needs a pan and drain line.
  • Switching from tank to tankless: often needs a larger gas line and new stainless or PVC venting.
  • Gas to electric or electric to gas: needs a new circuit or gas line.
  • After-hours or weekend installs.

Tank vs tankless for a Tulsa home

A tank water heater costs less up front and works during a power outage if it is gas. A family of 4 usually does well with a 50 gallon tank.

A gas tankless unit costs about twice as much to install but lasts close to 20 years and does not run out of hot water. It needs a yearly descale flush. Tankless works best when the home already has a large gas line and a good spot for venting on an outside wall.

Removing and disposing of the old tank

An old tank weighs 100 to 150 pounds empty and holds sediment that adds weight when drained. Installers carry a hand truck and drain the tank at the install site before moving it, which keeps water off floors and stairs. Scrap metal recyclers sometimes take old steel tanks for a small fee, but most installers simply include haul-away and disposal in the quoted price.

Ask what the installer does with your old unit; most either recycle the steel or dispose of it properly, and this should already be part of the installed price rather than a separate line item added later.

How a water heater installation works

  • The plumber checks the old unit, the gas or electric supply, venting and space.
  • You get a written price with the model, size and warranty.
  • The plumber pulls a City of Tulsa permit.
  • Water and gas or power are shut off, and the old tank is drained and removed.
  • The new unit is set, connected, and fitted with a new T&P valve, discharge pipe and expansion tank if needed.
  • The plumber fills the tank, checks for leaks, lights or powers it and tests the venting.
  • The old tank is hauled away.

Repair or replace your water heater

Repair makes sense when the tank is under 8 years old and the problem is a part: a thermocouple, gas valve, heating element, thermostat or drain valve. These repairs usually cost $150 to $600.

Replace when the tank leaks, is over 10 years old, or the repair quote is more than half the cost of a new unit. Most tank warranties run 6 to 12 years, so check the label before paying for a repair.

Tulsa factors that affect your water heater

Many Tulsa homes have the water heater in the garage or attic. Garage units must sit 18 inches off the floor if they are gas. Attic units work in summer heat above 120°F, which wears out valves and drain pans faster.

Tulsa gas service comes from ONG (Oklahoma Natural Gas) and electric service from PSO. Both list rebates from time to time for efficient units, so ask the plumber or check their sites before you buy.

Water heater installation near you

This service covers Tulsa, including Midtown, Brookside, South Tulsa and Kendall-Whittier, plus Broken Arrow, Owasso, Bixby, Jenks and Sand Springs. If your water heater is leaking now, close the cold water valve on top of the tank and turn the gas valve to Pilot or switch off the breaker.

Before you book: Tulsa price and problem guides

Next steps for Tulsa homeowners

Questions Tulsa homeowners ask

How long does water heater installation take?

A like-for-like tank swap takes 3 to 5 hours. A switch to tankless takes 6 to 10 hours because of new gas and vent work.

Do I need a permit to replace a water heater in Tulsa?

Yes. The City of Tulsa requires a permit for water heater replacement. A licensed plumber pulls it as part of the job.

What size water heater do I need?

1 to 2 people: 30 to 40 gallons. 3 to 4 people: 40 to 50 gallons. 5 or more: 50 to 75 gallons, or tankless.

Can I install a water heater myself in Tulsa?

Gas water heaters involve gas lines, venting and carbon monoxide risk. Hire a licensed plumber so the job meets code and passes inspection.

Is an expansion tank required?

Many Tulsa homes have a closed system because of a pressure regulator or backflow device. In that case code calls for an expansion tank, which adds $150 to $350.

How often should I flush a water heater?

Flush a tank once a year to remove sediment. Descale a tankless unit once a year.

Related services

Tell us the problem. We share your request with a licensed local pro.

Get a quote
Get a quote