Tulsa Plumbing and Air logoTulsa Plumbing & Air

Repiping in Tulsa, OK

Repiping in Tulsa replaces a home's old galvanized, polybutylene or leaking copper supply lines. A whole house repipe in Tulsa typically costs $4,000 to $15,000 and takes 2 to 5 days for an average home. Most repipes today use PEX pipe instead of copper because it handles freezing better and costs less to install. Repiping replaces all the supply lines, not drains or sewer lines.

  • Upfront price ranges
  • Licensed local pros
  • Tulsa County ZIPs only

Get a free quote

Takes 30 seconds. We share your request with a local pro.

Do you own the home?
Plumber using an acoustic leak detector on a kitchen tile floor in Tulsa, OK
Repiping in Tulsa, OK: typical work a licensed Tulsa-area pro handles.

Signs your home needs a repipe

  • Low water pressure throughout the house, especially with galvanized steel pipe.
  • Rust-colored water from multiple fixtures, not just one.
  • Two or more pinhole leaks in copper pipe within a couple of years.
  • Polybutylene pipe (gray plastic, common in homes built roughly 1978 to 1995), which cracks at fittings.
  • Frequent leaks behind walls or under the slab that keep recurring in different spots.
  • A home inspection that flags galvanized or polybutylene pipe before a sale.

Signs a repipe estimate seems too low

  • No mention of a permit or inspection in the written quote.
  • No pressure test included after the new lines are installed.
  • A price far below other quotes for the same home size and fixture count.
  • No clear statement of which pipe material, PEX or copper, is being used.

Fixtures typically shut off during a repipe

  • Kitchen and bathroom sinks: water off during active work hours, usually restored by evening.
  • Showers and tubs: same daytime shutoff pattern as sinks.
  • Washing machine supply: often left for last so laundry can run between work days.
  • Outdoor spigots: reconnected near the end since they are lower priority than interior fixtures.
  • Ice maker line: typically rerouted along with the kitchen sink supply during the same work session.

Want a real price for your home?

Get a quote

Manifold (home-run) PEX systems

A manifold or home-run PEX system runs an individual line from a central manifold to each fixture, instead of branching pipe through the walls. It uses more pipe but makes future repairs easier since each fixture can be shut off individually at the manifold without affecting the rest of the house.

A manifold system also tends to deliver more even water pressure to multiple fixtures running at once compared with an older branch-style layout.

Repiping and water pressure after the job

A repipe often improves water pressure noticeably in homes with old galvanized pipe, since rust buildup inside galvanized steel narrows the inside diameter over decades. PEX and copper keep their full diameter, so two fixtures can run at once without the pressure drop common in galvanized systems.

Partial repipe option

Some homes only need a partial repipe, replacing just the kitchen or one bathroom's supply lines if the rest of the house pipe is in better condition. This costs less than a whole house job but is only worth it if the remaining pipe is a newer material in good shape, not more old galvanized or polybutylene pipe waiting to fail next.

Choosing a repipe contractor's scope

  • Confirm whether drywall patching and texture matching are included or billed separately.
  • Ask whether the quote includes a pressure test certificate after the work is done.
  • Confirm which fixtures get new shutoff valves as part of the job.
  • Ask how disposal of old pipe, especially old galvanized or polybutylene, is handled.

How a plumber estimates total pipe footage

Before quoting a repipe, a plumber counts fixtures (sinks, tubs, showers, washing machine, ice maker, outdoor spigots) and measures the distance from the water heater and main shutoff to each one. A typical 2,000-square-foot single-story home needs roughly 300 to 500 feet of PEX pipe for a full repipe, while a two-story home or one with a spread-out floor plan needs more due to longer vertical runs.

Repipe scheduling around weather

Repiping that requires exterior wall access or crawlspace work is easier to schedule outside Tulsa's hardest freeze weeks in January and February, since open wall cavities lose heat faster during the work. Most plumbers still repipe year-round, but ask about extra precautions, like temporary insulation at open access points, if the job falls during a cold snap.

What happens to drain lines during a repipe

A standard repipe replaces supply lines only, the pipes that bring water to fixtures, not the drain lines that carry wastewater away. If a home's cast iron or clay drain lines are also failing, that is a separate job, sometimes bundled together to share labor and wall-opening costs but quoted and billed as its own line item.

Whole house repipe cost in Tulsa

Price depends on how many fixtures, whether walls are drywall or plaster, and whether the home is slab-on-grade or has a crawlspace or basement for easier access.

Home sizeTypical cost (PEX)Typical cost (copper)
1,200 – 1,800 sq ft, 2 bath$4,000 – $7,000$6,000 – $10,000
1,800 – 2,800 sq ft, 2 – 3 bath$6,000 – $10,000$9,000 – $14,000
2,800+ sq ft, 3+ bath$9,000 – $15,000$12,000 – $20,000

Living in the house during a repipe

  • Most repiping jobs allow the family to stay in the home during the work.
  • Water is typically off during the day and restored each evening, so plan showers and dishes around that window.
  • Set aside a few gallons of drinking water per day for the job's duration, since taps will not run during work hours.
  • Pets and small children should be kept away from open wall or attic access points for safety during active work.

Comparing repipe quotes from different plumbers

Quote itemWhy it matters
Pipe material and brandPEX brands vary in warranty length and fitting type
Number of fixtures includedA missed fixture means a change order mid-job
Patch and texture scopeDetermines if drywall repair is a separate cost
Permit included or separateCity of Tulsa permit fees add to the total
Pressure test includedConfirms no leaks before walls are closed

PEX vs copper for repiping

Most Tulsa repipes today use PEX because of cost and because it holds up better during hard freezes like the February 2021 cold wave. Copper is still used for exposed runs near water heaters or where local code requires it.

PEXCopper
Material costLowerHigher
Freeze resistanceBetter, flexes someCan split when frozen
Expected life40 – 50 years50 – 70 years
Installation speedFaster, fewer jointsSlower, more soldering
Resale perceptionAccepted, widely usedSometimes seen as premium

Repiping and old shutoff valve replacement

Many homes with original galvanized plumbing also have original gate valves at the main shutoff, which can seize over the years and fail to fully close in an emergency. Replacing these with modern ball valves during a repipe is a small added cost that makes future shutoffs more reliable.

Repiping and fixture upgrades

Many homeowners replace old shutoff valves, sink angle stops, and the main shutoff valve at the same time as a repipe, since the walls are already open. This adds a modest cost, often $200 to $600 total, but avoids opening the same wall again a few years later for a failed valve.

Replacing an old gate-style main shutoff valve with a modern ball valve during a repipe makes future shutoffs faster and more reliable in an emergency.

Repiping around a finished basement or crawlspace

Homes with a crawlspace, common in parts of Sand Springs and older Tulsa neighborhoods, often cost less to repipe than slab homes because the plumber can run new PEX lines beneath the floor instead of through walls. A finished basement adds cost if drywall has to be cut and patched to reach pipe runs.

Repiping and insurance considerations

Some homeowners insurance policies offer a discount once a home has polybutylene or galvanized pipe replaced, since these materials are linked to more water damage claims. Ask your insurance agent whether a completed repipe lowers your premium or removes a pipe material exclusion from the policy.

Repiping with existing finished walls and texture

  • Drywall is cut in strips along the pipe run, usually 1 to 2 feet wide per access point.
  • A plumber who also offers patch work closes and tapes the openings; texture matching is often a separate trade or add-on cost.
  • Homes with popcorn ceilings or custom texture may need a specialist for an exact match after repiping work in the ceiling.
  • Ask upfront whether the quote includes patch and texture, or only patch with texture matching extra.

What a repipe replaces

A repipe replaces the supply lines that bring fresh water to every fixture: sinks, tubs, toilets, the water heater and outdoor spigots. It does not replace drain lines or the sewer line, which are separate systems. If your drains or sewer line are also old, ask about doing that work at the same time to avoid opening the same walls twice.

How a whole house repipe works

  • The plumber maps the existing pipe routes and plans new runs, often through attics, closets and chases to limit wall damage.
  • You get a written price with pipe material, number of fixtures and any drywall patching included.
  • Water is shut off at the main, and new PEX or copper lines are run to each fixture.
  • Old pipe is capped or removed, and new lines are pressure-tested for leaks.
  • Walls and ceilings are patched, though painting and texture matching are often a separate cost.
  • A City of Tulsa permit and inspection apply to repiping; ask your plumber to confirm before work starts.

How long a repipe takes and what to expect

Most homes take 2 to 5 days: 1 to 3 days to run new pipe with the water off during work hours, and additional time for wall patching. Plan for limited water access during the day, usually restored each evening, and expect some drywall cutting even with careful routing through attics and closets.

Repiping vs spot repairs

If a home has had one or two isolated leaks, a spot repair or reroute makes more sense than a full repipe. A repipe is worth the cost when the whole system is near the end of its life: galvanized pipe over 40 years old, polybutylene pipe at any age, or copper with repeated pinhole leaks in different spots.

Next steps for Tulsa homeowners

Questions Tulsa homeowners ask

How much does it cost to repipe a house in Tulsa?

Whole house repiping typically costs $4,000 to $15,000 depending on home size, number of bathrooms and pipe material.

How long does repiping take?

Most homes take 2 to 5 days, including the new pipe installation and wall patching.

Is PEX pipe reliable?

Yes. PEX is widely used across the country and handles freezing better than copper. Most modern repipes in Tulsa use PEX.

Will my walls be damaged during a repipe?

Some drywall cutting is usually needed to reach pipe runs, though attic and closet routing limits it. Patching is often included; painting may be separate.

Do I need a permit to repipe my house in Tulsa?

Yes, a City of Tulsa permit applies to whole house repiping. A licensed plumber pulls it as part of the job.

How do I know if I have polybutylene pipe?

It is gray plastic pipe, common in homes built roughly 1978 to 1995. A plumber can confirm it during an inspection.

Related services

Tell us the problem. We share your request with a licensed local pro.

Get a quote
Get a quote